- 您现在的位置：买卖IC网 > Sheet目录476 > MDEV-900-NT (Linx Technologies Inc)TRM 900 NT MASTER DEV SYSTEM
The Range Test Area
The board features an MT Series remote control transcoder with two push
buttons, a buzzer and an LED. The two boards in the kit are populated
differently so that the button inputs on one board are outputs on the other
board. Figure 9 shows the differences.
To achieve maximum range, keep objects such as your hand away
from the antennas and ensure that the antennas on the boards have
an unobstructed line-of-sight path to each other. Range performance is
determined by many interdependent factors. If the range you are able to
achieve is significantly less than specified by Linx for the products you are
testing, then there is likely a problem with either the board or the ambient
RF environment in which the board is operating. First, check the battery,
switch positions, TX output power setting and antenna connection.
Check the range performance on different channels. Next, measure the
receiver’s RSSI voltage with the transmitter turned off to determine if
ambient interference is present. If this fails to resolve the issue, please
contact Linx technical support.
Board A
Figure 9: The Development Board Range Test Section
Board B
The PC Control Area
The PC Control Area is used with a daughter board to connect the
module’s Command Data Interface to a PC. This advanced feature is a
serial data interface for configuration and data transfer. One USB interface
When a button is pressed on one board, the status of both buttons is
captured, encoded into a data stream, and transmitted. The data
recovered by the receiving board is decoded and the transcoder’s data
board is included with the development kit. Additional USB interface boards
or an RS-232 interface board can be purchased separately.
lines are set to replicate the states of the buttons, driving either the buzzer
or the LED. A confirmation packet is then sent to the transmitting board
activating the Confirm LED.
To activate this area of the board, the module’s DATA and T/R_SEL lines
must be routed to the transcoder. This is accomplished by setting the
Mode Select switch to the right position and the Evaluation Select switch to
the middle position.
2
1
2
1
After the boards have been configured, place Board A on a flat surface
and turn it on. Turn on Board B and press button S1. The buzzer on Board
3
4
3
4
A will sound and the Confirm LED on Board B will light up. The usable
range of the link in your environment can be ascertained by carrying Board
B away from Board A. Switch SW11 has been provided to continuously
transmit the LED activation without having to hold down a button.
As you near the maximum range of the link in your area, it is common for
the signal to cut in and out as you move. This is normal and can result from
other interfering sources or fluctuating signal levels due to multipath effects.
The areas in which this occurs are commonly called “nulls” and simply
walking a little farther will often restore the signal.
– 8 –
Figure 10: PC Interface Boards
The top DIP switch (1) controls the TRPT/PKT line on the module. This
line selects between transparent data transmission and packet data
transmission. Slide it to the left for transparent data and to the right for
packet data.
The bottom DIP switch (1) controls the CMD_DATA_BAUD line on
the module. This is the data rate for the CDI and has no effect on the
over-the-air data rate. Slide to the left for 57,600bps and to the right for
9,600bps.
– 9 –
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MDEV-GPS-SG
KIT MASTER DEV GPS SG SERIES
MDEV-GPS-SR
KIT MASTER DEV GPS SR SERIES
MDEV-LICAL-HS-ES
KIT MASTER DEV HS ES RF MODULES
MDEV-USB-QS
KIT DEV MASTER USB QS SERIES
MF11-0010005
THERMISTOR NTC 100OHM -+5% PROBE
MF51E103F3950C
THERMISTOR NTC PREC -+1% 3950K
MG-300-A-9V-R
SENSOR DIGITAL GAUGE 300PSI LCD
MG-5000-B-MD-R
SENSOR 5000 PSI 4-20 MA 1/8 NPT
相关代理商/技术参数
MDEV-900-TT
制造商:Linx Technologies Inc 功能描述:TRM 900 TT MASTER DEV SYSTEM 制造商:Linx Technologies Inc 功能描述:RF Development Tools TT Series Master Development System
MDEV-916-ES
功能描述:KIT MASTER DEVELOP 916MHZ ES SRS RoHS:否 类别:RF/IF 和 RFID >> 过时/停产零件编号 系列:ES 标准包装:1 系列:- 类型:用于 200/300 系列的欧盟开发套件 适用于相关产品:Zensys RF 模块 所含物品:开发板，模块，编程器，软件，线缆，电源 其它名称:703-1019Q3225667
MDEV-916-ES-RS232
功能描述:射频开发工具 ES Master Dev Sys 916MHz, RS232 Module
RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-916-ES-USB
功能描述:射频开发工具 ES Master Dev Sys 916MHz, USB Module
RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-916-SC-P
功能描述:KIT MASTER DEVELOP 916MHZ SC SRS RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
MDEV-916-SC-S
功能描述:KIT MASTER DEVELP 916MHZ SCS SMD RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
MDEV-GNSS-GM
制造商:Linx Technologies Inc 功能描述:KIT MASTER DEV GNSS GM SERIES 制造商:Linx Technologies Inc 功能描述:Master Development System for the GM Series GNSS Receiver Module 制造商:LINX TECHNOLOGIES 功能描述:Master Development System for the GM Series GNSS Receiver Module
MDEV-GNSS-TM
制造商:Linx Technologies Inc 功能描述:KIT MASTER DEV GNSS TM SERIES 制造商:Linx Technologies Inc 功能描述:Master Development System for the TM Series GNSS Receiver 制造商:LINX TECHNOLOGIES 功能描述:Master Development System for the TM Series GNSS Receiver